Brady 3481 Manuale Utente Scaricare il pdf (Pagina 24)

Home
Brady
Stampanti per fotografie
3481
Manuale Utente

Scaricare
Condividere

Condivisione
Aggiungi ai miei manuali
Stampa

3.1 Loading Media

Begin loading as follows:

Œ Raise the Access Cover.

• Rotate the Printhead Latch forward and raise the Printhead Assembly.

Ž Slide the Media Guide out away from the frame and then lower it to the

down position.

• If using roll media, the Media Hub can accept 3.0-inch (76mm) and 1.5-

inch (38mm) cores. To use 1.5-inch cores, first slide off the 3 Inch Hub by

grasping and then pulling it firmly outward.

• Proceed according to the type of media you are using: either go to Section

3.1.1 for Roll Media or go to Section 3.1.2 for Fan-Fold Media.

1 2 ... 19 20 21 22 23 24 25 26 27 28 29 ... 139 140

(DO NOT print this page) 1
Copyright Information: 3
Listed 4
Printer Overview 7
Getting Started 7
Setting Up the Printer 7
Using the Front Panel 8
Maintenance and Adjustments 8
Troubleshooting 9
Specifications 9
1.0 About the Printer 11
1.0.1 Standard Features 12
Present Sensor 14
RS-422 Serial Interface* 14
Twinax/Coax Interface 14
1.1 Option Installation 15
1.2 Hardware Components 16
2.0 Unpacking the Printer 17
2.0.1 Inspection 18
2.0.2 Additional Requirements 18
2.1.1 Print Quality Controls 19
 Direct Thermal Facesheet 20
3.0 Installation 21
3.0.1 Communications 22
3.1 Loading Media 24
3.1.1 Roll Media 25
3.1.2 Fan-Fold Media 26
3.2 Media Sensor Adjustment 27
3.3 Loading Ribbon 28
3.4 Quick Media Calibration 30
3.5 Outputting Labels 31
3.5.2 On-Demand Dispensing 33
3.5.3 Cutting 35
4.0 Operation 37
Print Test Labels 39
4.0.4 Indicator Lights 40
4.0.5 LCD 40
4.0.6 Resetting the Printer 41
4.1 The Menu System 42
4.1.2 Media Settings 44
4.1.3 Print Control 45
4.1.4 Printer Options 47
4.1.5 System Settings 49
PRINTER KEY 51
UPGRADE PRINTER CODE 51
²DISABLED 55
300 DOTS PER INCH 55
203 DOTS PER INCH 55
4.1.6 Communications 57
4.1.7 Diagnostics 63
4.2 Display Messages 64
4.3 Quick Test Mode 66
4.3.2 Configuration Label 67
4.3.3 Quick Ribbon Test Label 68
4.3.4 Dot Test Pattern Label 69
4.3.5 Validation Label 70
4.3.6 User Defined Label 70
5.0 Media Sensor Calibration 71
72
5.1 Printhead Adjustments 81
5.1.2 Burn Line Adjustment 82
5.2 Printhead Replacement 83
5.3 Maintenance Schedule 84
5.3.1 Cleaning the Printhead 85
6.0 Problem Resolution 93
Fault Messages: 97
Warning Messages: 102
6.2 Hex Dump Mode 103
7.0 General Specifications 105
Environmental Requirements 106
Mechanical 106
Printing Specifications 106
Wound out labels only 107
Approved Media 108
Appendix A 109
Appendix B 111
Bar Code Summary Data 115
Appendix C 119
Appendix D 121
Appendix E 123
Creating a Menu Language: 124
Appendix F 129
Warranty Information 131
Warranty Service Procedures 132
General Warranty Provisions 133
Limitation of Liability 133
Glossary 135

Commenti su questo manuale

Nessun commento

Brady 3481 Manuale Utente Pagina 24

Commenti su questo manuale